Automatyczna Waga Shell Load v2.0 do naważek

Moderatorzy: wierzba, P_iter

NoOne
Posty: 3
Rejestracja: niedziela, 20 lutego 2022, 20:49
Kontakt:

Automatyczna Waga Shell Load v2.0 do naważek

Post autor: NoOne »

Cześć wszystkim Elaborantom,

Jeśli jesteście zainteresowani projektem który spędzał mi sen z powiek przez ponad rok i uważacie go za interesujący i przydatny polecam jego wsparcie.

Projekt dotyczył stworzenia automatycznej wagi do naważek prochu o dokładności której odchyła nie byłaby wyższa niżeli 0.05 gn.

Poniżej link:

https://github.com/Psyche607/Shell_Load-powder-measure

OPIS (przepraszam że po angielsku 'Laughing' )

Shell_Load-powder-measure
The Shell Load powder measure packs unparalleled powder-measuring accuracy in a compact package. The Shell Load is an effective, accurate powder-measuring tool. The accuracy is between 0,02 gn - 0,05 gn with fast dosage under 5s per dosage.



Precision Accuracy The hopper holds amount of smokeless powder for about 200 - 300 rounds, and can dispense anywhere between 0-1000 grains with a +/-0.05 grain accuracy.


LCD Display This one-piece unit features an LCD display that ensures accurate data input.



Firmware functions:

Automatic calibration of the keyboard on the first boot,
Automatic scale calibration by any mass of the weight set for example 10g weight / 20g weight,
Menu that allows user to set the following functions parameters:

Ability to save 10 different configurations depending on the type of ammunition and gunpowder types in relation to the weight that we want to achiev,
Ability to set the Units Grains (Gn) / Grams (g) as a default value to take measurements,
Recalibration Shell Load Scale,
Enable - Autotare,
Set point when Shell Load Scale shoud start to dosing in more slowly way and more accurate to get finall dosage,
Set the point when Shell Load Scale shoud start dosing super slowly way and in maximum accurate way to get finall dosage,
Set the Fast dosing speed,
Set the super accurate slow dosing speed,
Set the tolerance value that is acceptable by user / Maximum weighted dosage deviation,
Set timout for dosing,
Set compensation value,
Reset to defaults,
Ability to upgrade firmware.
Dashboard:

Set the dosage to weight (gn/g)
Current actual weight of the dosage,
Tare Shell Load manually,
START/STOP Dosing,
Information about:
Dosing process Finished returning OK,
Dosing process Finished but weight is Overdosed,
Dosing process took too long and give an error of Timeout.
SHELL LOAD v 2 0

SHELL LOAD v. 2.0.pdf

What is needed:

There are two options:

A) You have to print on 3d Printers in two technologies SLA / FDM or just on SLA Printer:

Firstly Print 3 main components:

On SLA/FDM Printer with the highest possible tolerance

BASE,
COMPUTER CASE,
SCALE
ONLY on SLA PRINTER !!! (Don't Print on FDM printer this can generate and accumulate electrostatic charges, leading to ignition of gunpowder.)

FUNNEL,
MOTOR GEAR,
PAN,
POWDER TUBE,
SNAIL.
Electronic / Firmware

The main computer unit is using Arduino with specially dedicated hat, with all connectors that you need and uploaded firmware. This part we will do for you in exchange for a small support that is neede to further develop this project.

If you think this project is great and you want to support us, give us oportunity for further developemnt. Click on the button "sponsor this project" - on the right side of this page

You can support this project with any amount, but if you pay the amount:

87€, we will make a hardware computer unit for you, and upload the newest firmware, next we send it in 3 weeks to address that you need:
For location:

Poland we send the package for 6€ by "Paczkomat",

For USA you have to send us 35€ more, to allow us, to send the package to you.

Other Countries send to us question about your location and we try to find the cheapest solution to send the item to you.

Any amount below the given values will always be a great support for us and we will be very grateful for it that you decided to support the development of our project, but it will not make it possible to make and deliver of a computer with software or any other element from this project.

Thank you for all your support !!!

The rest of electronic / mechanicall items that will be needed:

1x Loadcell 100g for normal accuracy / or Loadcell 50g for for very accurate measurements,
1x HX711 Modul that will be connected to "Loadcell" 50g/100g,
1x LCD Display 1602 with I2C Interface,
1x 5 Buttons AD Key Pad,
1x Power Supply min 12V 1A with Plug 5,2x2,1,
1x NEMA17 Stepper Motor,
1x calibration weight (5g / 10g / 20g it is relevent what you choose, everything will work),
SCREWS:

19x M3x06      / For main computer TOP and all internalss (LCD, KEBOARD, MAINBOARD), Scale TOP.
2x M3x16      / For Loadcell mount,
2x M3x25      / For mounting Boul to Loadcell,
4x M3x8      / Bottom of te computer unit,
4x M3x12      / NEMA17 MOUNT,
1x M3 screw tap
Logic diagram of cable connections:



Below Accuracy proof of the Shell Load v2.0 - Click it to watch.

IMAGE ALT TEXT
Below calculation of measures as a statistics:


B. We can make for you everything - This option will be added in the future. Laughing
Awatar użytkownika
matthius
Posty: 689
Rejestracja: niedziela, 13 września 2015, 17:08

Post autor: matthius »

Rozważ proszę umieszczenie opisu projektu także po polsku.
Według mnie, dziwnie wygląda oferta kierowana przez Polaka na polski rynek, w której zamiast języka polskiego jest łamany angielski.
Nie każdy posługuje się tym językiem na tyle biegle, aby odszyfrowywać polglish.

Sam pomysł wydaje się fajny i wart rozwijania. Bawiłem się rok temu w coś podobnego - chciałem zrobić przystawkę do wag Radwaga. Zabrakło mi jednak doświadczenia w druku 3D, a nie chciałem wydawać na hobbystyczny projekt więcej kasy, niż kosztuje Chargemaster Lite.

Myślę, że warto rozważyć opcję, w której dostarczałbyś komplet wydrukowanych części i dostęp do aktualizacji oprogramowania.
Arduino i peryferia łatwo kupić za niewielkie pieniądze. Dobrej jakości druk 3D, zwłaszcza w technice SLA, wymaga już większego wydatku na drukarkę lub zlecenie wydruku profesjonalistom.
NoOne
Posty: 3
Rejestracja: niedziela, 20 lutego 2022, 20:49
Kontakt:

Shell Load v.2.0

Post autor: NoOne »

W związku z sytuacją geopolityczną :)

Projekt został otwarty, udostępniono wszystkie elementy do jego wykonania.

Miłej zabawy i dużo precyzyjnej amunicji życzy zespół SHELL LOAD.

https://github.com/Psyche607/Shell_Load-powder-measure

https://www.thingiverse.com/thing:5257762

Jeśli uznacie projekt za wart uwagi prosimy o wsparcie.
ODPOWIEDZ